Cisco 2600 Series Router Password Reset

Lab Objectives

•   Break the boot sequence when powering on the Cisco 2600 Series router to place yourself in ROM monitor mode.
•   Change the configuration register to 0×2142 to make the router bypass the contents of NVRAM when booting then reset the router
•   (Option 1) – Once booted, place yourself into privileged mode and copy the start up-config to the running config. Afterward, you may change the line password or enable password and write the configuration by to NVRAM by issuing the copy run start •   (Option 2) – Once booted, place yourself into privileged mode and do a write erase to clear the contents of the NVRAM.
•   Now change the configuration register back to 0×2102 to boot set the router to boot normally and load the NVRAM contents upon boot.

Lab Instruction

As shown below is a Cisco 2651XM router that has a console password on the device. With such a password you cannot access exec mode without authenticating this password correctly. When buying routers used, you may commonly be faced with scenario.

Router con0 is now available   Press RETURN to get started.   User Access Verification   Password:

Step 1. Power cycle the router or power on the router initially. While the router is booting you’ll need to break the boot sequence to boot the router into bootrom, you do this by holding down CTRL and pressing PAUSE BREAK. Do this repeatedly till you are placed at the bootrom prompt.

System Bootstrap, Version 12.2(8r) [cmong 8r], RELEASE SOFTWARE (fc1) Copyright (c) 2003 by cisco Systems, Inc. C2600 platform with 262144 Kbytes of main memory   monitor: command “boot” aborted due to user interrupt rommon 1 >

Step 2. Change the configuration register so that the router will ignore the contents of the NVRAM when booting into Cisco IOS. Set the configuration register to 0×2142 and boot the router.

rommon 1 >confreg 0×2142 rommon 2 >reset

Step 4 (Option 1) – After the router has booted into Cisco IOS, you’ll be prompted by the initial configuration dialog, type n here and press enter and you’ll be placed into user mode. Now you’re able to place your self into privileged mode by typing enable. Once in privileged mode you can copy the startup configuation to the running configuration and then change the passwords manually then saved the configuration by to NVRAM by typing copy run start.

— System Configuration Dialog —   Would you like to enter the initial configuration dialog? [yes/no]: n     Press RETURN to get started!   Router>enable Router#copy start run Destination filename [running-config]? 506 bytes copied in 3.868 secs (168 bytes/sec) IMAROUTER#configure terminal IMAROUTER(config)#enable secret NEWENABLEPASSWORD IMAROUTER(config)#line con 0 IMAROUTER(config-if)#password NEWPASSWORD IMAROUTER(config-if)#end IMAROUTER#copy run start Destination filename [startup-config]? Building configuration… [OK] IMAROUTER#

Step 4 (Option 2) – After the router has booted into Cisco IOS, you’ll be prompted by the initial configuration dialog, type n here and press enter and you’ll be placed into user mode. Now you’re able to place your self into privileged mode by typing enable. Once in privileged mode you can erase the contents of NVRAM by issuing the write erase command.

— System Configuration Dialog —   Would you like to enter the initial configuration dialog? [yes/no]: n     Press RETURN to get started!   Router>enable Router#write erase Erasing the nvram filesystem will remove all files! Continue? [confirm] [OK] Erase of nvram: complete Router#

Step 5. Once you’ve performed a password reset or NVRAM sanitation, you’ll need to set the configuration register back to 0×2102 so the router will boot normally and load the NVRAM contents upon a reboot or powerfailure.

Router#configure terminal Router(config)#config-register 0×2102 Router(config)#end